進口氣動角座閥 特性介紹 Introduction to characteristics of imported pneumatic angle seat valve

氣動角座閥按照安裝方式包括內螺紋連接款，外螺紋+ 卡套管焊接款，焊接款，法蘭款，快裝款，除此之外我司還可提供全錫青銅材質角座閥;

可以在任何方向安裝∶橫向，縱向，傾斜。

雙動型和單動型產品能提供的口徑規格從3 /8 英寸到4 英寸，可從阻塞錘上下兩端關閉，而單動型閥門從阻塞錘下端開啟。

Pneumatic angle seat valves include internal thread connection, external thread + ferrule welding, welding, flange and quick installation. In addition, our company can also provide angle seat valves made of all tin bronze;

It can be installed in any direction: transverse, longitudinal and inclined.

Double acting and single acting products can provide caliber specifications from 3 /8 inches to 4 inches, which can be closed from the upper and lower ends of the blocking hammer, and the single acting valve can be opened from the lower end of the blocking hammer.

氣動角座閥工作原理 working principle

單作用：由一個二位三通電磁閥控制。導向介質壓力進入執行器，作用于活塞，使閥芯穿梭于閥腔中實現打開或關閉閥門。閥芯復位通常是借助于氣動執行器中的彈回彈簧來完成。

Single acting: controlled by a two position three-way solenoid valve. The pressure of guiding medium enters the actuator and acts on the piston to make the valve core shuttle in the valve chamber to open or close the valve. The valve element reset is usually completed by means of the spring in the pneumatic actuator.

1.雙向常閉（N.C.）Two way normally closed (N.C.)介質從閥芯下方流入，可避免水錘作用。介質在閥芯上方流入，將受到水錘擠壓;

The medium flows under the valve core to avoid the action of water hammer. If the medium flows above the valve core, it will be squeezed by water hammer;

常閉型（N.C.）介質從閥芯上方流入，介質從閥芯上方流入會造成"水錘"效應Normally closed (N.C.) medium flows from above the valve core, which will cause "water hammer" effect

常開型（N.O.）介質從閥芯下方流入Normally open (N.O.) medium flows from below the valve core

雙作用：配置的閥門中，沒有彈回彈簧，導向介質既用來打開閥門，也用來關閉閥門。

Double acting: there is no spring in the configured valve, and the guiding medium is used to open and close the valve.

特點Characteristics of pneumatic flange angle seat valve

Y 型內腔設計，流量比普通閥門大30 %以上;超長使用壽命Y-shaped inner cavity design, the flow is more than 30% larger than that of ordinary valves; Long service life

閥桿采用V 型密封，保證閥門在長時間運轉后仍能完好無損The valve rod adopts V-shaped seal to ensure that the valve is still intact after long-term operation

加長防錘形導向和防塵密封圈Extended spindle guide and wiper seal. 

閥座設置一定的角度，從而在閥門打開時提供盡可能大的流量。The valve seat is set at an angle to provide the greatest possible flow when the valve is opened

當閥門處于打開狀態時，通過執行器頂端的視窗可以看到紅色的位置指示桿。When the valve is open, the red position indicator can be seen through the window at the top of the actuator

自動調節雙層填料密封蓋Self-adjusting, double packing glands.

易安裝Easy to install 

反應敏捷Fast Response 

水擊作用極小Water hammer-free 

汽控接口可在360°上任意選定位置Motor control interface on the 360°Random designation position

無水擊作用（流向閥座下）Water hammer-free (Flow below seat)

適用介質范圍

閥門的最小工作壓力是根據閥門的型號和腔內流體壓力的峰值差異確定的，由此也可確定對應閥門的型號。空氣、水、酒精、油、石油燃料油、鹽溶液、蒸汽等（所有適用于 AISI304、316不銹鋼或青銅 RG5 的流體介質）;按所選型號和運行參數，閥門的工作壓力應位于 0~16/25Bar ，（蒸汽介質在 180℃C時，工作壓力為0~10 Bar)

介質溫度∶ -10℃ ~180℃

介質粘度∶≤600cst（mm2/s）

The minimum working pressure of the valve is determined according to the model of the valve and the peak difference of the fluid pressure in the cavity, so the model of the corresponding valve can also be determined. Air, water, alcohol, oil, petroleum fuel oil, salt solution, steam, etc. (all fluid media suitable for AISI304, 316 stainless steel or bronze Rg5); According to the selected model and operating parameters, the working pressure of the valve should be 0~16/25bar (when the steam medium is 180 ℃, the working pressure is 0~10 bar)

Medium temperature: -10 ℃ ~180 ℃

Maximum viscosity of medium: 600cst (mm 2/ s）

氣動角座閥執行機構∶

塑料活塞式氣動頭，鋁合金活塞式氣動頭，不銹鋼活塞式氣動頭

環境溫度;max.60℃位置反饋

可選附件∶行程限位過程位置控制器

Pneumatic flange angle seat valve actuator:

Plastic piston pneumatic head aluminum alloy piston pneumatic head stainless steel piston pneumatic head

Ambient temperature; Max.60 ℃ position feedback

Optional accessories: stroke limit process position controller

"水錘效應"是指在水管內部，管內壁光滑，水流動自如。當打開的閥門突然關閉，水流對閥門及管壁，主要是閥門會產生一個壓力。由于管壁光滑，后續水流在慣性的作用下，迅速達到最大，并產生破壞作用，這就是水力學當中的"水錘效應"。也就是正水錘。在水力管道建設中都要考慮這一因素。相反，關閉的閥門在突然打開后，也會產生水錘.叫負水錘，也有一定的破壞力.但沒有前者大。

"Water hammer effect" means that inside the water pipe, the inner wall of the pipe is smooth and the water flows freely. When the open valve suddenly closes, the water flow will produce a pressure on the valve and pipe wall, mainly the valve. Because the pipe wall is smooth, the subsequent water flow quickly reaches the maximum under the action of inertia, and has a destructive effect, which is the "water hammer effect" in hydraulics. That is, positive water hammer. This factor should be considered in the construction of hydraulic pipelines. On the contrary, water hammer will also occur when the closed valve is suddenly opened Called negative water hammer, it also has certain destructive power But not as big as the former.

應用范圍：

空氣凈化、化工、紡織、印染、食品加工、制藥、環保、水處理，啤酒飲料灌裝設備，發泡機械等行業

Application scope:

Air purification, chemical industry, textile, printing and dyeing, food processing, pharmaceutical, environmental protection, water treatment, beer and beverage filling equipment, foaming machinery and other industries