基本參數 Basic parameters

規格尺寸Specification and size：G1/2～2"

閥體材質Body material：316L不銹鋼（耐酸堿），316L stainless steel (acid and alkali resistant)

結構Structure：縮徑，浮動球直通（硬密封球閥）Reduced bore, floating ball straight-through (hard seal ball valve)

工作溫度Working temperature:0-120°C，選擇（三元乙丙橡膠：EPDM）,0-200°C，選擇（氟橡膠密封：FKM）

閥桿材料Stem material:默認316L，可選（哈式合金鋼或哈式）

陶瓷球芯，耐磨、耐腐蝕、密封性優良、使用壽命長（10萬次以上）Ceramic ball core, wear-resistant, corrosion resistant, excellent sealing performance, long service life (more than 100000 times)

輸入電壓：直流DC6V/12V/24V，交流AC220V Input voltage: DC 6V/12V/24V, AC 220V

全開→全閉時間：12.5秒和3秒（DN25及以下），7.5秒（DN25以上）“斷電復位”功能；帶開關位置反饋功能 Full open → full close time: 12.5 seconds and 3 seconds (DN25 and below), 7.5 seconds (DN25 and above) "power off reset" function; With switch position feedback function

功能：二線、三線電源控制 Function: two-wire and three-wire power control

適用流體:水、空氣、油類、酸堿腐蝕性介質和化工低粘度流體。（防水IP等級：IP65）Applicable fluid: water, air, oil, acid-base corrosive medium and chemical low-viscosity fluid. (Waterproof IP grade: IP65)

產品結構 Product mix

① 直流/交流減速電機（DC6-24V/AC220V）

② 316L閥桿（根據不同酸堿可選哈式合金鋼B或C）

③ 不銹鋼316閥體 

④ 陶瓷球芯（剛玉陶瓷氧化鋁）

⑤ PPS耐腐蝕密封片 

⑥ 瓷密封片 

⑦ 開關指示燈

性能特點 Performance characteristics

1.密封性能：球芯和閥座配對研磨，貼合度極高，密封優良。因球閥開關時有刮板作用，不易發生卡阻泄漏現象.

Sealing performance: the ball core and valve seat are lapped in pairs, with high fit and excellent sealing. Because the ball valve has the function of scraper when it is opened and closed, it is not easy to get stuck and leak

2.耐磨性能，耐腐蝕性能：球芯和閥座均采用高硬度、高性能的氧化鋁陶瓷，耐磨性和耐腐蝕性特佳，球芯和閥座不容易因磨損和腐蝕導至密封失效，密封壽命長達10萬次以上

Wear resistance and corrosion resistance: the ball core and valve seat are made of high hardness and high performance alumina ceramics, with excellent wear resistance and corrosion resistance. The ball core and valve seat are not easy to lead to seal failure due to wear and corrosion, and the seal life is more than 100000 times

3.啟閉扭矩：1、球芯和閥座配對研磨，貼合度極高，需很小作用力就可以達到密封要求；2、球芯和密封座結構及減背壓技術. 上述兩點直接的結果是球閥的啟閉扭矩遠遠小于傳統球閥，僅為傳統球閥的1/4.

1. The ball core and valve seat are lapped in pairs, and the fit degree is very high, and the sealing requirements can be met with a small force; 2. Ball core and seal seat structure and back pressure reduction technology The direct result of the above two points is that the opening and closing torque of the ball valve is far less than that of the traditional ball valve, which is only 1/4 of that of the traditional ball valve

功能模式與配線圖說明 Description of function mode and wiring diagram

1.普通二線模式（默認款）說明：過轉換開關或中間繼電器改變電流方向控制電機來驅動球閥的開和關，控制線為兩芯線。（顛倒正負極，或稱正反轉）Description of common two-wire mode (default): change the current direction through the transfer switch or intermediate relay to control the motor to drive the opening and closing of the ball valve. The control wire is two-core wire. (Reverse the positive and negative poles, or positive and negative)

SW與OPEN短接，電動球閥打開，到位后并保持 Short circuit between SW and OPEN, open the electric ball valve, and keep it in place

SW與CLOSE短接，電動球閥關閉，到位后并保持 SW and CLOSE are short-circuited, and the electric ball valve is closed and maintained in place

適用于DC6V、DC12V、DC24V球閥。SW為雙聯開關 Applicable to DC6V, DC12V and DC24V ball valves. SW is a duplex switch

2.斷電復位·二線模式 （僅DN20-DN25）說明：功能相當于電磁閥，常開或常閉，二線斷電自動復位，啟閉到位電機即斷電。（常閉型：通電開，斷電關；常開型：通電關，斷電開），因為是電容充電，所以建議先充電15分鐘以上再使用 Power off reset · two-wire mode (only DN20-DN25) description: the function is equivalent to the solenoid valve, normally open or normally closed. The two-wire power off automatically resets, and the motor is powered off when it is opened or closed in place. (Normally closed type: power-on and power-off; normally open type: power-on and power-off), since it is capacitor charging, it is recommended to charge for more than 15 minutes before use

SW閉合，電動球閥打開，到位后并保持 SW is closed, electric ball valve is opened, and it is kept in place

SW斷開，電動球閥關閉，到位后并保持 SW is disconnected, the electric ball valve is closed, and it remains in place

適用于DC9~24V球閥 Applicable to DC9~24V ball valve

3.斷電復位·三線模式（僅DN20-DN25）說明：三線二控斷電自動關閉，正常控制相同于普通三線控制，斷電狀態下，球閥實現自動關閉。（改變內部接線方式，也可實現斷電打開）可靠性更高 Power off reset · three-wire mode (only DN20-DN25) description: three-wire two-control power off automatically closes, the normal control is the same as the ordinary three-wire control, in the power off state, the ball valve automatically closes. (Changing the internal wiring mode can also realize power-off and opening) with higher reliability

SW與紅線相連，電動球閥打開，到位后并保持 SW is connected to the red line, and the electric ball valve is opened and kept in place

SW與綠線相連，電動球閥關閉，到位后并保持 SW is connected to the green line, the electric ball valve is closed, and it is kept in place

適用于DC12V~DC24V球閥 Applicable to DC12V~DC24V ball valve

4.普通三線模式 說明：電源控制線為三芯線，其中一芯線與公共線通時為一種流道狀態，另一芯線與公共線通時為另一種流道狀態 Description of common three-wire mode: the power control line is three-core wire, one of which is in one channel state when one core wire is connected with the common wire, and the other is in another channel state when the other core wire is connected with the common wire

SW與紅線相連，電動球閥打開，到位后并保持 SW is connected to the red line, and the electric ball valve is opened and kept in place

SW與綠線相連，電動球閥關閉，到位后并保持 SW is connected to the green line, the electric ball valve is closed, and it is kept in place

適用于DC6V、DC12V、DC24V球閥 Applicable to DC6V, DC12V and DC24V ball valves

5.交流220V三線模式 說明：電源控制線為三芯線，接入電壓為AC220V，其中N、L1兩端接220V電壓，電動球閥打開；N、L2兩端接220V電壓，電動球閥關閉 Description of AC 220V three-wire mode: the power control line is three-core wire, and the access voltage is AC220V, where N and L1 are connected with 220V voltage, and the electric ball valve is opened; 220V voltage is connected at both ends of N and L2, and the electric ball valve is closed

N、L1兩端接220V電壓，電動球閥打開，到位后并保持 Connect 220V voltage at both ends of N and L1, open the electric ball valve, and keep it in place

N、L2兩端接220V電壓，電動球閥關閉，到位后并保持 Connect 220V voltage at both ends of N and L2, close the electric ball valve, and keep it in place

適用于AC220V球閥 Applicable to AC220V ball valve

6.二線/帶位置反饋信號DC24V  說明：電源控制線為兩芯線，位置反饋信號線為三芯線（又稱五線控制），球閥開關到位后分別可以輸出無源信號，適用于DC24V電動球閥 Two-wire/DC24V with position feedback signal Description: the power control line is two-core wire, and the position feedback signal line is three-core wire (also known as five-wire control). After the ball valve is switched in place, passive signals can be output respectively, which is applicable to DC24V electric ball valve

SW與OPEN短接，電動球閥打開，到位后并保持。同時LS.1接通并給出開到位置信號，即BL與WT相通 SW and OPEN are short-circuited, and the electric ball valve is opened and held in place. At the same time, LS.1 is connected and gives the signal of opening to the position, that is, BL is connected with WT

SW與CLOSE短接，電動球閥關閉，到位后并保持同時LS.2接通并給出關到位置信號，即YW與WT相通  SW and CLOSE are short-circuited, and the electric ball valve is closed. When it is in place, LS.2 is connected and the signal of closing to the position is given, that is, YW and WT are connected

適用于DC24V球閥 Applicable to DC24V ball valve