(RA10VO)進口變量柱塞泵 產品特點 Product features

法蘭連接按SAE-UNC或SAE公制 Flange connections to SAE-UNC or SAEmetric

2個泄油口 2 leakage ports

允許高轉速 Allow high speed

良好的吸油性能低噪音 Good oil absorption and low noise  

功率/重量比高  High power / weight ratiol

驅動軸可承受軸向和軸向載荷retz品牌  The drive shaft can bear axial and axial loads

控制范圍寬 Wide control range

用于多回路系統的通軸驅動選配 Through shaft drive selection for multi loop system

(RA10VO)進口變量柱塞泵 參數值 Parameter value

1、進口工作壓力范圍Input operating pressure range

油口（S）的絕對壓力Absolute pressure at port S（A）

Pabs min.………………0.8bar 

Pabs max……………………………………3bar

2、出口工作壓力范圍 Output operating pressure range

油口B的壓力Pressure at port B

公稱壓力Nominal pressure PN………………………………280bar 

尖峰壓力Peak pressure Pmax……………………………… 350bar 

3、殼體泄油壓力Case drain pressure

油液泄油最大壓力（在油口L，L1），最多可比S口的進口壓力高05bar，但是不能超過絕對壓力2bar.Maximum pressure of leakage fluid (at ports L,L1),Maximum 7 psi (0.5 bar) higher than input pressure at port S, but not higher tHan 30 psi(2 bar)absolute. 

4、流動方向 Direction of flow

S至B（StoB）

5、數值表（理論數值，未考慮ηmh祁ηv；近似值）

Table of values (theoretical values without considering n mh and ny;values rounded)

注∶以上值在吸油口的絕對壓力為1bar時有效，如果流量減小或進口壓力增加，轉速可增加。Notes.:Values shown are valid for an absolute pressure cof 1 bar at suction port.If the flow is reduced or if the inlet pressure is increased the speed may be increased.

油液Fluid

1、工作介質Fluid∶MR20S（Q/TCNK12-2001）

2、工作粘度范圍 Operating viscosity range

為了得到最佳效率和使用壽命，我們建議工作粘度（在工作溫度下）在一下范圍中選擇∶

v opt=最佳工作粘度16mm2/s~36mm2/s

針對油箱溫度（開式回路）

For optimum efficiency and service life we recommend thatthe operating viscosity (at operating temperature) be selectf in the range:

v opt=opt. operating viscosity 16~36mm2/s 

referred to tank temperature (open loop circuit). 極限粘度范圍Limits of viscosity range

在極端工況下，下列數值有效∶（The following values are valid for extreme operating conditions∶）

v min=10 mm2/s

短 時，在80℃的最高允許漏油溫度下

for short periods at max. leakage oil temperature of 80℃v min=1000mm2/s

短時，冷啟動時for short periods upon cold start. 

3、溫度范圍Temperature range tmin=-20℃; tmax=+80℃

4、過濾Fi Itration

為了保證軸向柱塞泵的正常運作，最低清潔度等級為∶ISO4406之16/19級，這可通過安裝過濾器來實現，油泵回油過濾精度為10um。

In order to ensure reliable operation of the axial piston unit,theoperating fluid must be maintained to a cleanliness class of at least: 16/19 to ISO4406. This may be achieved with filter elements, cleanliness class of pump leakage fluid 10um。