產品用途 Product use

1.適用于各種通用機械場合，銷釘方塊結構最高使用1000轉/分，滾針軸承結構最高轉速可達4000轉/分，建議實際使用轉速在最高轉速的50%以內使用 It is applicable to all kinds of general mechanical occasions. The maximum speed of pin block structure can be 1000 rpm, and the maximum speed of needle bearing structure can be 4000 rpm. It is recommended that the actual speed be used within 50% of the maximum speed

2.適用于聯結空間同一平面上兩軸夾角每節極限轉動角度為45度，允許使用角度30度以內 Applicable to the included angle of two shafts on the same plane of the connecting space. The limit rotation angle of each section is 45 degrees, and the allowable angle is within 30 degrees

3.所提供的快速鎖緊裝置僅有公差為H7的成品孔，帶標準的鍵槽或六角孔可選，可非標定制不同安裝結構 The provided quick locking device only has finished hole with tolerance of H7, with standard keyway or hexagonal hole optional, and different installation structures can be customized non-standard

4.適用于聯結空間同一平面上兩軸軸線夾角≤30°的傳動 Applicable to the transmission with the included angle of two axes on the same plane of the connecting space ≤ 30 °

5.傳遞公稱轉矩11.2-1120N.m.（可定制更大扭矩）Transmit nominal torque 11.2-1120 N.m. (larger torque can be customized)

6.常規鍵槽頂絲孔，可按照要求定制不同孔型和固定方式 Conventional keyway jackscrew hole can be customized with different hole types and fixing methods according to requirements

7.允許兩軸間夾角在限定的范圍內隨工作需要而變動 The included angle between the two shafts is allowed to change with the work needs within the limited range

結構特點 Structural features

產品材質： 常規40Cr高碳鋼,可定制304 316 等特殊材質 Product material: conventional 40Cr high carbon steel, customized 304 316 and other special materials

1、適用于聯結空間同一平面上兩軸3≤458tordm，的傳動場合，傳遞公稱轉矩11.2-1120N.m. It is applicable to transmission occasions where two shafts on the same plane of the connecting space are 3 ≤ 458tordm, and the transmission nominal torque is 11.2-1120N. m

2、每節最大軸間夾角45&ordm The maximum angle between shafts of each section is 45&ordm

3、成品孔H7，可根據要求，開鍵槽、六方孔和四方孔 Finished hole H7, keyway, hexagonal hole and square hole can be opened as required

4、允許兩軸間夾角在限定的范圍內隨工作需要而改變 The included angle between the two shafts is allowed to change with the work needs within the limited range

5、有帶滑動軸承及滾針軸承兩種型式，根據用戶要求而定。帶滾針軸承的，動態負載高軸承游隙小，最高轉速可達4000rpm，帶滑動軸承的最高轉速為1000rpm  There are two types of sliding bearing and needle bearing, which are determined according to user requirements. With needle roller bearing, the dynamic load is high, the bearing clearance is small, the maximum speed can reach 4000 rpm, and the maximum speed with sliding bearing is 1000 rpm