(RDA2FM)進口定量柱塞馬達 產品特點 Product features

油口A或B的最高壓力,額定壓力可達40MPa， 峰值壓力可達45MPa The maximum pressure of oil port a or B, the rated pressure can reach 40MPa, and the peak pressure can reach 45MPa

開式和閉式回路，規格10...180 Open and closed circuits, specifications 10... 180

流動方向:順時針旋轉A到B,逆時針旋轉B到A Flow direction: clockwise rotation a to B, counterclockwise rotation B to a

輸出轉速與輸入流量成正比而與排量成反比  The output speed is proportional to the input flow and inversely proportional to the displacement

驅動扭矩隨馬達的高壓側和低壓側的壓降加大而增大  The driving torque increases with the increase of the pressure drop on the high-pressure side and low-pressure side of the motor

仔細選擇所提供的排量.其規格可與各實際應用情況匹配  Carefully select the displacement provided. Its specification can match the actual application

良好的功率/重量比  Good power / weight ratio

整體錐形柱塞帶有用于密封的活塞環  Integral tapered plunger with piston rings for sealing

工作粘度范圍 Working viscosity range

液壓油，礦物油 Hydraulic oil, mineral oil

為了獲得最佳效率和使用壽命.我們推薦工作粘度（在工作溫度下）在以下范圍內選擇∶In order to obtain the best efficiency and service life, we recommend that the working viscosity (at the working temperature) be selected in the following range:

Vopt=最佳工作粘度16..36mm2/S  Vopt= optimum working viscosity 16..36mm2/S

閉式回路中針對回路溫度.開式回路中針對油箱溫度 For circuit temperature in closed circuit. For oil tank temperature in open circuit

油液的過濾 Filtration of oil

油液過濾得越干凈.油液的清潔度越好.軸向柱塞元件的使用壽命也就越長。為了保證元件的正常工作 最低的清潔度等級是retz品牌∶NAS 1638，9級或 ISO/DIS 4406，18/15級  The cleaner the oil is filtered, the cleaner the oil is The longer the service life of the axial piston element. In order to ensure the normal operation of components, the minimum cleanliness level is NAS 1638, level 9 or iso/dis 4406, level 18/15

油液溫度很高時.清潔度等級至少應為∶NAS 1638，8級或 ISO/DIS 4406，17/14級  When the oil temperature is very high The cleanliness grade shall be at least NAS 1638, Grade 8 or iso/dis 4406, grade 17/14

轉速范圍 Speed range

最低轉速n min沒有限制,在需要平穩運行的  There is no limit on the minimum speed of N min, when it needs to run smoothly

場合最低轉速n min不能低于50rpm。最高轉速風工作參數  The minimum speed n min of the occasion shall not be lower than 50rpm. Working parameters of maximum speed wind

(RDA2FM)進口定量柱塞馬達 數據值（理論值）