技術參數 Technical paramete

(黃銅)進口內螺紋平衡閥具有關截止功能，產品攜帶有測量接頭，方便與測量設備的快速連接，當系統調試后可將鎖定裝置開啟，方便日后可關閉靜態閥進行管路維護與檢修，結束后可以直接將閥門恢復到設定好的最大行程處，避免二次調試。The internal thread balance valve of the static balance valve has relevant cut-off functions. The product carries a measuring connector to facilitate the quick connection with the measuring equipment. After the system commissioning, the locking device can be opened to facilitate the closing of the static valve for pipeline maintenance and repair in the future. After the completion, the valve can be directly restored to the set maximum stroke to avoid secondary commissioning

尺寸:G1/2-2" 

工作溫度:-10~100℃

承壓等級:PN16

工作介質∶空調冷熱水、乙/丙二醇溶液連接方式∶

性能特點∶ Performance characteristics

Y型直流閥體結構，配合精確加工的錐形閥瓣 Y-type DC valve body structure, with precisely machined conical valve disc

精確流量控制，數字手輪開度指示 Precise flow control, digital handwheel opening indication

開度鎖定簡單，具有關斷功能，通過手輪進行關斷 Simple opening locking, with off function, and off by hand wheel

具有自密封壓力/流量測量口 With self sealing pressure / flow measuring port

(黃銅)進口內螺紋平衡閥 零部件材質 Component material

①閥體：黃銅 Valve body: Brass

②閥芯：黃銅 Valve core: Brass

③閥座密封：PTFE  Seat seal: PTFE

④閥蓋：黃銅 Bonnet: Brass

⑤閥桿：黃銅 Valve stem: Brass

⑥鎖定芯桿：黃銅 Locking core rod: Brass

⑦閥桿密封：EPDM  Stem seal: EPDM

⑧手輪塑料：ABS Handwheel plastic: ABS

⑨測量嘴：黃銅 Measuring nozzle: Brass

測量精度示意圖  Schematic diagram of measurement accuracy

內螺紋平衡閥在開度≥50%時，誤差不得大于±5%；10%≤開度≤50%時，誤差不得大于±10%。故在產品選型時，建議設計流量下閥門開度大于50%為宜，同時為保證現場調試余量，閥門盡量設置在75%開度左右RETZ When the opening of static balance valve is ≥ 50%, the error shall not be greater than ± 5%; When 10% ≤ opening ≤ 50%, the error shall not be greater than ± 10%. Therefore, during product selection, it is suggested that the valve opening should be greater than 50% under the design flow. Meanwhile, in order to ensure the on-site commissioning margin, the valve should be set at about 75% opening as far as possible.

安裝說明 Installation instructions

內螺紋平衡閥安裝前應確保系統內無雜物，請注意介質的流向與閥體上的流向標記一致，一般安裝于系統的回水管，當與動態壓差平衡閥配套使用時，安裝于供水管。通常與彎頭或水泵連接時，需要保持一定的直管段安裝距離；當與彎頭連接時，遵循閥前5d，閥后2d原則；當與水泵連接時，遵循10d原則RETZ Before installing the static balance valve, ensure that there are no sundries in the system. Please note that the flow direction of the medium is consistent with the flow direction mark on the valve body. It is generally installed in the return pipe of the system. When it is used with the dynamic differential pressure balance valve, it is installed in the water supply pipe. Generally, when connecting with elbow or water pump, a certain installation distance of straight pipe section shall be maintained; When connected with the elbow, follow the principle of 5D in front of the valve and 2D behind the valve; When connected with the water pump, follow the 10d principle.