(黃銅)進口內螺紋動態平衡電動調節閥 技術參數 Technical paramete

內螺紋動態平衡電動調節閥結構分為流量調節結構和動態平衡結構兩部分  RETZ structure of dynamic balance electric control valve is divided into two parts: flow control structure and dynamic balance structure

流量調節結構可完成閥門流量的設定和調節，配合執行器可實現閥門的電動調節、開關功能 RETZ flow regulating structure can complete the setting and regulation of the valve flow, and cooperate with the actuator to realize the electric regulation and switching functions of the valve

動態平衡結構可實現閥門流量的動態平衡，該結構的核心部件為感壓膜片和彈簧，感壓膜片感應閥門入口和平衡閥芯內腔之間的壓（P1-P2），在此壓差作用下調節可變流道的流通面積，保持壓差（P1-P2）基本恒定，從而保持流量不變  RETZ dynamic balance structure can realize the dynamic balance of the valve flow. The core components of the structure are the pressure sensing membrane and the spring. The pressure sensing membrane senses the pressure (P1-P2) between the inlet of the valve and the inner cavity of the balance valve core. Under the effect of this pressure difference, the flow area of the variable flow channel is adjusted to keep the pressure difference (P1-P2) basically constant, so as to keep the flow unchanged

尺寸：G1/2"-2"  G1/2"-2"

工作溫度：0~95℃ Working temperature: 0~95℃

承壓等級：PN16  Pressure bearing grade: PN16 

工作介質∶水、乙二醇溶液 Working medium: water and glycol solution

連接方式∶G螺紋 Connection method: G thread

流量特性：等百分比  Flow characteristics: equal percentage

閥泄漏率 ：小于KVS值的0~0.05%  Valve leakage rate: less than 0 ~ 0.05% of kVs value

驅動材質 ：壓鑄合金鋁支架，鋼質傳動齒輪，同步馬達，浮動式開關 Driving material: die casting alloy aluminum bracket, steel transmission gear, synchronous motor, floating switch

流量誤差：＜５％ Flow error: ＜ 5%

控制信號：0-10VDC / 4-20mA  Control signal: 0-10VDC / 4-20mA

工作壓差范圍：30-400kpa Working pressure difference range: 30-400kpa

執行器防護等級：1P44  Protection grade of actuator: 1P44

工作電源 ：AC24V/AC220V 50/60Hz Working power supply: AC24V / AC220V 50 / 60Hz

驅動控制 ：浮點型，智能型（DC0~10V/4~20mA)，開關型，選配無源反饋 Drive control: floating point type, intelligent type (dc0 ~ 10V / 4 ~ 20mA), switch type, optional passive feedback

輸出扭力 ：1500N，帶斷電手動開關功能  Output torque: 1500N, with power-off manual switch function

(黃銅)進口內螺紋動態平衡電動調節閥流量特性

零部件材質 Component material

閥體：鍛造黃銅 Valve body: forged brass

閥芯∶黃銅 Valve core: Brass

閥桿∶不銹鋼  Valve stem: stainless steel 

彈簧：不銹鋼 Spring: stainless steel 

密封圈∶PTFE Sealing ring: PTFE

閥桿密封：EPDM Stem seal: EPDM

V型免維護補償密封 V-type maintenance free compensation seal

性能特點∶ Performance characteristics

等百分比控制特性·保持調節閥兩端壓差恒定 Equal percentage control characteristic · keep the pressure difference at both ends of the regulating valve constant

電子預設定最大流量，方便現場調試 Electronic preset maximum flow, convenient for field debugging

具有故障自動診斷和報警功能，電源帶過載保護功能·行程自動檢測功能 With automatic fault diagnosis and alarm function, the power supply has overload protection function and automatic travel detection function

調節閥芯采用直行程設計，提供調節型和開關型兩種執行器 The regulating valve core adopts the straight stroke design, and provides two types of actuators: regulating type and switching type

內螺紋動態平衡電動調節閥安裝說明 Installation instructions

1.安裝前請詳細閱讀說明書，檢查產品型號和參數，根據要求設定工作電壓和輸入信號 Before installation, please read the instructions carefully, check the product model and parameters, and set the working voltage and input signal as required

2.盡可能保證垂直安裝，預留空間以方便維護 Vertical installation shall be ensured as much as possible, and space shall be reserved for convenient maintenance

3.安裝時應注意保證水流方向與閥體上箭頭所指方向一致 During installation, pay attention to ensure that the water flow direction is consistent with the direction indicated by the arrow on the valve body

4.建議設計系統旁路連通，灌裝時應該由旁路將管路中雜質沖洗干凈，否則可能會引起閥門堵塞 It is recommended to design the bypass connection of the system. During filling, the impurities in the pipeline should be flushed by the bypass, otherwise the valve may be blocked

5.安裝時應保證閥門前后預留一定長度的直管段，一般在進口預留管道直徑10倍長度的直管段，出口預留管道直徑5倍長度的直管段  During installation, a certain length of straight pipe section shall be reserved before and after the valve. Generally, a straight pipe section 10 times the length of the pipe diameter shall be reserved at the inlet and a straight pipe section 5 times the length of the pipe diameter shall be reserved at the outlet