進口夾殼聯軸器 產品用途 Product use

1.適用于低速和載荷平穩工作場合,對中精度要求低,精度要求低,適用于轉速1000轉以下的工作場合 Suitable for low speed and stable load applications, with low requirements for centering accuracy and accuracy. Suitable for applications with rotational speeds below 1000 rpm

2.直連安裝方式,無彈性體無緩沖，對中精度要求低,精度要求低，適用于低速和載荷平穩工作場合 Direct connection installation, no elastomer and no buffer, low centering accuracy requirements, low accuracy requirements, suitable for low speed and stable load working situations

結構特點 Structural features

1.中間無彈性體，一般都是吊裝，中間有個吊環，吊住兩端的軸，軸孔直徑是通徑，一般采用立式裝用，中間部位開槽裝有懸吊環卡住兩端設備的軸頭，來傳遞轉矩 There is no elastic body in the middle, which is generally used for hoisting. There is a lifting ring in the middle, which holds the shafts at both ends. The diameter of the shaft hole is the drift diameter. Generally, vertical installation is used. The middle part is slotted and equipped with a lifting ring to clamp the shaft heads of the equipment at both ends to transmit torque

2.用于反應器攪拌軸過長，分兩段制造時兩攪拌軸的聯接，若立式減速機輸出軸與反應器攪拌軸聯接選用夾殼聯軸器，需在定貨時提出，以便對輸出軸尺寸用非標要求 It is used for the connection of two mixing shafts when the reactor mixing shaft is too long and manufactured in two sections. If the vertical reducer output shaft and the reactor mixing shaft are connected using a clamshell coupling, it is necessary to propose it when ordering, in order to use non-standard requirements for the output shaft size

基本參數 Basic parameters and dimensions

1-夾殼  2-半環  3-螺栓  4-螺母  5-外后止動墊圈

1-Clamping shell 2-Half ring 3-Bolt 4-Nut 5-Outer rear stop washer

注：必須在容許值的范圍內使用該聯軸器 Note: The coupling must be used within the allowable range

注意事項Matters needing attention

1、兩軸軸線對中精度低，結構和形狀比較復雜，制造及平衡精度較低，只適用于低速和載荷平穩的場合 The alignment accuracy of the two axis axes is low, the structure and shape are relatively complex, and the manufacturing and balancing accuracy is low. It is only suitable for situations with low speeds and stable loads

2、通常最大外緣的線速度不大于5m/s，當線速度超過5m/s時需要進行平衡校驗。為了改善平衡狀況，螺栓應正、倒相間安裝。夾殼聯軸器不具備軸向、徑向和角向的補償性能 Generally, the linear speed of the maximum outer edge is not greater than 5 m/s. When the linear speed exceeds 5 m/s, a balance check is required. To improve the balance, the bolts should be installed in alternating phases. Clamping couplings do not have axial, radial, and angular compensation performance.