產品描述 Product Description

進口電磁遙控浮球閥加裝了常開或常閉型電磁閥電控裝置，具有雙保險作用，即使停電或電浮球失靈，也能控制水位，絕不會讓水位超過規定的位置，電動浮球閥可以設置啟閉水位，解決主閥頻繁啟閉。該閥廣泛用于高層建筑、城市生活用水、消防、工況企業的水池，水塔的進水管道中

The imported electromagnetic remote control float valve is equipped with a normally open or normally closed electromagnetic valve electric control device, which has a dual safety function. Even if there is a power outage or the electric float valve fails, the water level can be controlled and will never exceed the specified position. The electric float valve can set the opening and closing water level to solve the problem of frequent opening and closing of the main valve. This valve is widely used in water tanks and inlet pipes of water towers in high-rise buildings, urban domestic water, firefighting, and operating enterprises

結構和主要零件材質 Structure and main component materials

結構形式為液控截止形式，按不同口徑采用橡膠膜片和活塞式連接閥蓋瓣開啟、關閉的形式 The structure is in the form of hydraulic control cut-off, with rubber diaphragm and piston type connection valve cover disc opening and closing according to different diameters

該閥由主閥、針閥、球閥、浮球閥和微型過濾器等組成，如圖所示 The valve consists of a main valve, needle valve, ball valve, float valve, and micro filter, as shown in the figure

主要零件材質 Main component materials

工作原理

關閉狀態：當主閥進口端水壓分別進入閥體及控制室，且主閥的外部球閥同時關閉，此時主閥處于關閉狀態。

Fully closed state: When the water pressure at the inlet end of the main valve enters the valve body and control room respectively, and the external ball valve of the main valve is closed at the same time, the main valve is in a fully closed state

開啟狀態：當主閥外部的球閥全開后，此時控制室內水壓全部釋放到管路下游，而主閥也呈現為開啟狀態。

Fully open state: When the ball valve outside the main valve is fully open, all the water pressure in the control room is released to the downstream of the pipeline, and the main valve also shows a fully open state

浮動調節狀態：調節主閥外部的球閥開度，使進水端流向控制室的水流和控制室流向下游的水流達到平衡，此時主閥處于調節浮動狀態。

Floating adjustment state: Adjust the opening of the ball valve outside the main valve to balance the water flow from the inlet end to the control room and the water flow from the control room to the downstream. At this time, the main valve is in the floating adjustment state

安裝與調試 Installation and debugging

1、主閥安裝于水池或高位水塔的進水管上，最佳安裝方式是水平安裝在管線上，閥蓋朝上，其他安裝方式也可達到操作功能。浮球閥安裝于水池和水塔內，以便遙控 The main valve is installed on the inlet pipe of the pool or high-level water tower, and the best installation method is to install it horizontally on the pipeline with the valve cover facing upwards. Other installation methods can also achieve operational functions. Floating ball valves are installed in the pool and water tower for remote control

2、安裝前要清除管道內的雜物，沖洗管道。安裝時要注意主閥體外水流標示箭頭，遵循方向安裝 Before installation, thoroughly remove any debris from the pipeline and flush the pipeline thoroughly. When installing, pay attention to the water flow arrow outside the main valve and follow the direction of installation

3、主閥前要裝一只閘閥和一只過濾器，主閥后也需裝一只間閥，以便于維修 A gate valve and a filter should be installed in front of the main valve, and a space valve should also be installed behind the main valve for maintenance purposes

4、試水時要慢慢開啟主閥前的閘閥，慢慢增加壓力，同時注意主閥體外的控制管路是否泄漏 When testing the water, slowly open the gate valve in front of the main valve, slowly increase the pressure, and pay attention to whether the control pipeline outside the main valve is leaking

5、為出廠時包裝方便，浮球閥裝于主閥上 For convenient packaging at the factory, the float valve is installed on the main valve

6、主閥導管進口處的微型過濾器要2~3個月清洗一次 The micro filter at the inlet of the main valve guide should be cleaned every 2-3 months